• Classic Looking Transmitter. ▋Transmitter specifications Item Specification Part Number: NET-M116G Type of control: 6 channel computer mixing RF: 2.4GHz Modulation: DMSS (Dual Modulation Spread Spectrum System) 6.4V Lithium Ferrite battery 2F1400(1400mA) Power source: *Optional 7.2V Li-ion battery available (2L3200) • Introduction ▋General Safety Precautions * It is very important to ensure that you DANGER observe the following precautions. If incorrect operation methods are used, there will This company cannot be responsible for any accident be a possibility of death or serious injury. Or failure that may occur from any modification of this product, use of non-genuine parts, natural disaster, or WARNING. • Introduction ▋Rechargeable Battery and Out-of-control and dangerous situations can be caused. When degraded servo movement is Battery Charger detected, immediately stop operating and check the battery power remaining, servos, etc.

Abide by t he fol low i ng to prevent potent ia l leakage, explosion, heat generation, and fire. • Contents ▊ System List ▋Contents Model Select 【 MODEL SELECT】 ・・・・・・・・ 47 ▊ Introduction Model Copy & Erase 【MODEL COPY/ERASE】 ・・・ 48 Model Type Select 【 TYPE SELECT】 ・・・・・・・ 50 Greetings ・・・・・・・・・・・・・・・・・・ 1 Model Name 【MODEL NAME】 ・・・・・・・・・ 51 Features ・・・・・・・・・・・・・・・・・・・ 1 Flight Mode Name 【FLIGHT MODE NAME】. • Preparation ▋Stick Length Adjustment Lock Undo the recessed set screw located at the tip of the control stick.

JR Propo Product Manual Download section, in the drop-down menusyou'll find links that allow you to download copies of JR Propo. Dragon ball z raging blast 2 pc utorrent. 14-Channel Transmitters.

Now rotate the entire stick to adjust its length. When finished, lock the recessed set screw. Unlock ▋Rubber Grip Attachment The included rubber grips may be attached to the back of the transmitter using the included tape.

• Preparation ▋Inserting and Removing the Transmitter Battery 1) To open the battery cover, lift the tab on the rear of the transmitter. The stock LiFe battery (2F1400 #04153) connects with a single connector. The optional Li-Ion battery (2L3200 #04158) connects using two connectors. Fit the rechargeable battery into the battery box, and close the battery cover, taking care not to pinch the lead wires.

• Preparation ▋Stick tension adjustment and throttle travel adjustment plate ▋Adjustment of the stick spring strength Screws(Black)×6 ① Remove the battery before carrying out any adjustments. ② Remove the screws from the six locations shown.

③ Adjust the springs to the desired spring tension. By carefully adjusting each of the screws, you can achieve a range of spring tensions. • Preparation ▋Receiver Connections Receiver Connections to the servos and the power supply. JR labels the channels on the receiver with names rather than numbers. From this point onward in the manual, the receiver channels will be described using their names. Harness connection Connection Chart Sensor Installation.

• Preparation ▋Using the transmitter and receiver. Receiver mounting location. ▋Please set up the antenna direction as shown The 2.4GHz band radio waves are very directional.

The receiver signal is very dependant on the direction of the antenna. Since the antenna receives radio waves from the sides rather than from the tip, please appropriately position the receiver antenna when installing the receiver in the model. • Preparation ▋2.4GHz Antenna Considerations 2.4GHz band radio waves have strong directionality so receiving sensitivity differs greatly depending on the direction of antenna orientation. The RG612BX receiver has integrated telemetry, and it therefore operates as a receiver and a transmitter at the same time.