Raven arms mp-25 manual DownloadRaven arms mp-25 manual. Free Pdf Download Simplify patient statements by sending them electronically to MedPrint. Exe uses 99 CPU i tried. The pistol must be in unloaded, uncocked condition before take down can be performed.

• Push the button in with the butt-end of your ballpoint pen, then lift the slide up and off of the main gun frame. • Apply the gun solvent to a cloth swatch and push it through the barrel with your wire brush. Do this twice to fully coat the inside of the barrel with solvent, then let it soak for a minute to break up any dirt or grime. • Apply more solvent to your soft cloth and rub down all the metal parts of the gun--including the inside and outside of the slide. Use a second cloth to dry off the solvent after letting it soak for a few seconds.

• Push several clean cloth swatches through the barrel with your wire brush to dry off the gun solvent. Keep running the swatches through until they come out dry and clean. • Apply gun oil to another cloth swatch and run this one through the barrel. The metal parts of the MP-25 need to be oiled to prevent rusting and corrosion.

Run two or three oil-soaked swatches through the barrel to ensure that it is completely coated. • Apply gun oil to a soft cloth and lubricate all the metal parts of the MP-25. Berserk golden age arc 1 english dubbed. • Place the slide back on the frame of the MP-25 and push the button back in with your pen. Press the slide down until it clicks back into place.

(THE FOLLOWING 3 PARAGRAPHS ARE QUOTED DIRECTLY FROM THE MANUAL) FIRING THE PISTOL After loading your Magazine, insert it into the bottom of the pistol handle and push it into the pistol as far as possible. Point your pistol in a safe direction and with your other hand firmly grasp the serrated portion of the Slide and pull it as far rearward as it will go. Release the Slide from it's rearmost position, allowing it to go forward of it's own accord. This procedure places the first cartridge into the chamber and the gun is ready for firing. Subsequent feeding and ejection operations are performed automatically until the pistol is empty. NOTE: Unless the pistol is already cocked, the safety must be in the 'FIRE' (F) position before the pistol can be cocked or loaded from the magazine supply. The pistol must be in unloaded, uncocked condition before take down can be performed.

Or Just Download The Ones You Want (DWG Only) TWA-01 Typical Potable Water & 01.1 Irrigation Service TWA-02 Typical Commercial Water Service TWA-03.0 CDR Boxes 4 Meters, 03.1 CDR Boxes 6 Meters & 03.2 CDR Boxes 8 Meters TWA-04 Typical Cul-De-Sac Water/Reuse Piping TWA-05 Sanitary Sewer Lateral TWA-06 Sanitary Cleanout. Uzli krepleniya keramogranita v dwg. Complete fan unit for tool-free mounting on surfaces. Air throughput from 20 - 900 m³/h, protection category IP 54 as standard.RAL 7035.

To remove the slide, use a blunt object (such as a lead pencil eraser) to push the Retainer, located in the back end of the Slide, forward until it stops (about 1/4'). While holding the Retainer depressed, gently lift the rearward portion of the Slide away from the Frame until it stops. Release the Retainer gently as it is spring loaded. Hold the rearward portion of the Slide up and push the Slide forward, off of the end of the gun. This procedure removes the entire Slide Assembly and is sufficient for normal cleaning and oiling. Clean the Barrel within a reasonable period of time after shooting. After the powder residue has been removed, give the Barrel bore a protective coat of oil.

ASSEMBLY Make sure the Recoil Spring is in the Frame. Place the Slide Assembly over the Barrel and pull rearward until it can be dropped down onto the Frame. Depress the Retainer into the Slide far enough to allow it to drop into its slot.